CHANGE-A-LOCK®, Logo

Orange, California       TOLL FREE     
(866) 546-2957

Established 1978

American Flag

Made in the USA

Shop by Category

02. Schlage®, Baldwin®, Emtek®, & Pegasus® (5 -pin key cylinder) Rekey Kit

Grid | List (1 to 3 of 3) « Prev | Next »
Grid | List (1 to 3 of 3) « Prev | Next »
The $12.95 SCHLAGE®, BALDWIN®, EMTEK® & PEGASUS® (5-pin key cylinder system) rekey kit by CHANGE-A-LOCK® contains everything necessary (except a common screwdriver) to rekey ANSI RATED 1 & 2 Grade for keyed Entrance, Lever Entrance, Single & Double cylinder Deadbolts and Handleset type locks. The kit will rekey 6 single cylinder locks. Each lock you put a key in is a single cylinder. A deadbolt keyed on both sides would count as 2 single cylinder locks. This rekey kit will rekey the Schlage® A50 & F51 series Knob Entrance, Schlage®'s new B200's & B300's Deadbolt series and Schlage's older 100, 200, 300, & 400 Deadbolt series locks. BALDWIN®, EMTEK®, & PEGASUS® uses the SCHLAGE® instructional sheets to rekey.

EACH KIT CONTAINS: Two precut keys, 6 sets of color coded pins for rekeying Single and/or Double cylinder type locks, detailed step-by-step instructions in both ENGLISH & SPANISH, and all specialty tools needed to rekey lock. To order EXTRA PIN SETS and/or EXTRA KEYS for your rekey kit please click on the desired rekey product list. All you may need is a common screwdriver to remove lock. The SCHLAGE®, BALDWIN®, EMTEK® & PEGASUS® rekey kit is not designed to work with any other manufacturer's locks.

Note: You must use the keys provided in rekey kit for rekeying. Pins match keys in kit and are not to be used to rekey with any other keys!

NOTE: OLD KEY is needed to take out cylinder plug then new key is used to rekey lock. Old keys can not be used to rekey locks using the CHANGE-A-LOCK® rekey kit for the cylinder pins will not work with old key.

SPECIAL NOTE: BALDWIN®, EMTEK® & PEGASUS® locks need to have the SCHLAGE® key cylinder for the rekey kit to work!

ALERT: SCHLAGE® 6-PIN KEY CYLINDER

Schlage®, Baldwin®, Emtek®, & Pegasus® 5-pin key cylinder locks often come with a 6-pin key cylinder. The 6-pin key cylinder only has bottom pins in the first 5-pin holes,with the 6th. pin hole position being empty. When you insert the key from the CHANGE-A-LOCK® rekey kit into the 6-pin key cylinder, and using the special instructional sheet to replace the bottom pins, the last hole after the tip of the key is the 6th. pin hole position.

Therefore, the 6th. pin hole position is not used when rekeying.

ALERT! SCHLAGE SecureKey® LOCKS

Do not use the CHANGE-A-LOCK® rekeying method with the new Schlage SecureKey® Locks. The Schlage SecureKey® locks have a + above the key slot. You can use the keys in the CHANGE-A-LOCK® rekey kit to have all your locks keyed alike. However, you will need to have a new "blue" reset SecureKey(TM) cut to match the CHANGE-A-LOCK® keys. Schlage® corporation has exclusive control over the new "blue" reset SecureKey(TM); therefore, we can not provide them at this time. The "blue" reset SecureKey(TM) can be purchased at your local home center.

Watch Schlage SecureKey® rekeying method: http://securekey.schlage.com/pages/home.aspx

ALERT! BALDWIN PRESTIGE SERIES® LOCKS

Do not use the CHANGE-A-LOCK® rekeying method for the new BALDWIN PRESTIGE Series® Locks. The Prestige Series(TM) locks use the new KWIKSET SMART KEY® method for rekeying. The newly design Baldwin® locks will have a small slot on the left side of the key cylinder slot which uses the KWIKSET SMART KEY® for rekeying lock. BALDWIN® LOCK COMPANY was recently purchased by the KWIKSET® CORPORATION. The Baldwin Prestige Series® locks now have the KWIKSET® key cylinder. Previously, BALDWIN® LOCKS had the SCHLAGE® key cylinder.

ALERT: WHAT TO DO IF KEY CAN NOT BE REMOVED AFTER LOCK HAS BEEN RE-KEYED. If your key cylinder has a screw-off end cap, tighten or loosen one or two notches at a time until you are able to remove key. If this does not work or if your lock cylinder does not have a screw-off end cap then refer to master keyed locks below.

MASTER KEYED LOCK:

Your lock may have been master keyed at one time. If key can not be removed once lock has been rekeyed, then remove the key cylinder again using the follower. Remove the follower to let the top pins and springs drop out of cylinder housing. If lock has been master keyed you will have more than 5 top pins for a 5 pin cylinder lock system. Refer to the directions on how to replace the 5 top pins of equal length and the 5 springs. Do not use the other pins which drop out of the cylinder housing!

If you have a 6 pin key cylinder system then replace the 6 pins of equal length and the 6 springs.

Privacy Notice:

CHANGE-A-LOCK.com will not share, sell, or otherwise disclose any of your personal or financial information with outside parties for any reason. All information you provide on this web site will be used by CHANGE-A-LOCK.com for the sole purpose of customer service and/or fulfillment of your order. We do not partner with any other businesses.  CHANGE-A-LOCK Guarantees your Privacy!

CHANGE-A-LOCK® never sells or discloses personal information to third party companies.